With the buttons pressed, turn on the power switch to the Apollo – hold down the knob/button combo for approximately 10 seconds until the LED lights on the front panel of the Apollo stop flashing.
Why is my Apollo not working?
Bad or defective data cables (FireWire or Thunderbolt) can cause many issues with Apollo / UAD devices. If your problem persists after performing the procedures listed above, we recommend replacing your data cable (FireWire or Thunderbolt) to eliminate that as a possible cause of the problem.
Can my Apollo twin overheat?
Improper ventilation will cause overheating and can damage the unit. The unit should sit level on its four rubber feet and be placed far enough away from other objects that the air vents on its chassis are not blocked. The unit should be situated away from heat sources, or other equipment that produces excessive heat.
How do you reset a UAD demo?
After these two additional courtesy resets are manually granted, the ONLY way to obtain any demo reset is to purchase any UAD-2 Powered plug‑in from the UA online store.
Why is my Apollo blinking?
If the Monitor volume knob on your Apollo is blinking and you have no audio output, then you may have the DIM function enabled with the DIM AMOUNT set too high in the Console application. The settings for the DIM function are found on the CONTROL ROOM strip.
How do I update my Apollo twin?
How do you turn on phantom power on Apollo twin?
Why are my UAD plugins not working?
Sometimes the cause is something simple, such as running out of resources to process UAD plug-ins or a UAD device getting unplugged from the computer, and other times the cause is less clear such as a failed data cable or a corrupt software installation.
Why does Apollo Twin get so hot?
The apollo has no fans, it has processing chips and tons of electronics. Electronics create heat, the aluminum chasis dissipates heat. Its basically a heatsink for the unit. So its normal for it to get hot, especially if your loading a lot of plugins or bouncing a session.
What is UAD console?
The Console application is the key to unlocking UA Audio Interface’s unique Realtime UAD Processing capabilities. It enables you to insert and control UAD plug-ins as well as route and monitor audio.
How do I get free UAD plugins?
All newly registered UAD-2 / Apollo products come with an included plug-in bundle free of charge. These bundles are a great way for new users to get started with UAD plug-ins right out of the box without the need for an additional purchase.
How do I uninstall UAD plugins?
Open the application named “Uninstall Universal Audio Software” by double-clicking its icon. 3. Click the “Uninstall UA Software” button in the Uninstall Universal Audio Software window. All UAD software is deleted and the uninstall process is complete.
How do you turn on Apollo solo?
How do you connect a microphone to Apollo twin?
How do I update my Apollo firmware?
Open the UAD Meter & Control Panel application by clicking its icon in the Mac OS X Dock. When prompted by the UAD software, update the Apollo firmware. Be sure to turn off Apollo after the firmware is installed on the device.
Can I use Apollo twin without computer?
“Standalone Use Although the Console application is required to utilize all Apollo Twin MkII features, the hardware unit can be used as a digital mixer with limited functionality without a Thunderbolt connection to a host computer.
What is pad on Apollo twin?
A “PAD” stands for Passive Attenuation Device. The circuitry in active mics may overload if the incoming signal from the capsule is too strong, causing audio signal distortion.
How do I reset my UAD console?
Hold the LEVEL, LOW CUT, and POLARITY buttons and power on the computer. After all front panel LEDs flash rapidly (after several seconds), release the controls allow Arrow to restart. Disconnect and then reconnect Arrow to complete the reset.
Can I use UAD plugins without hardware?
Here’s the list of all the UAD plugins without hardware you can run: Brainworx Shadow Hills Mastering Compressor. Softube’s Eden WT800 Bass Amplifier. Softube’s ChandlerLimited Curve Bender Mastering EQ.
Can you connect two Apollo twins?
When connecting multiple Apollo devices, they must be daisy-chained to the same Thunderbolt port on the computer. In the wiring example diagram, the lower Apollo is designated as the monitor (master) unit. Connect speakers (including ALT speakers, if enabled) to the monitor unit only.
How do you use the Apollo Twin hardware?
How do I download UAD console?
Download and install Universal Audio Console Open your downloads folder and uncompress the UAD . zip file. Double-click the . pkg or .exe installer file and follow the on-screen instructions to install the software.
Can you use Apollo twin without console?
Yes, you can use it without Console, but I’d recommend you to try using it first. If you don’t use Console and monitor via Ableton (or any DAW), you’ll lose near-zero-latency monitoring while tracking.
How do I open UAD console?
How do I use console recall?
What plugins come with Apollo Twin MkII?
Right out of the box, Apollo Twin MkII provides a suite of incredible analog emulation plug-ins including the world’s only authentic Teletronix LA-2A, 1176LN, Pultec EQs, and the Unison-enabled UA 610-B Tube Preamp.
Which plugins are free with Apollo twin?
SCOTTS VALLEY, CA • April 03, 2019 — Now through June 30th, 2019, customers who buy and register any new Apollo Twin MkII, Apollo Twin USB, or Arrow audio interface are eligible to receive free UAD plug-ins from Antares, Manley, and UA as part of the UA Platinum Vocal Promo.